Reboot MIG Welder 250Amp Gas Gasless MIG/Stick/Lift TIG Welder 6 in 1 Flux Core/Solid Wire MIG Inverter Welding Machine MMA MIG MAG Stick Welder with WP17-FV Tig Torch

Brilliant bit of kit great value for money loads of powers perfect size and weight

Absolutely spot on welder. No issues and easy to set up.

Have had this a few months and so far, I am pleased with it. Was bought as an addition to my stick welder. First set-up took about 30mins from opening the box to being ready to play (and included a few glances at the instructions!!). First actual test use on non-project material found the 'near enough' power setting pretty quick as the auto-feed speed is dictated by the input setting for the power. I did find a few issues that I'm not 100% about.. first one was the feed length of the protruding wire... found it easier to keep track of when I used it without the pink end shroud hiding the copper tip but that could be my inexperience with wire feed welders.. but it's worked well since removing the shroud... the second is the amount of spatter.. getting a lot more than I would have expected. I have clean workpieces and don't use anti-spatter spray.. maybe I should! It came with a decent sized reel of flux-cored wire that I've not fully used and won't change it for the sake as it is doing a perfectly good welding job for what I want.. but when I do, I'll spend decent money on quality f/c wire and see if that could be the issue. The first big test was to repair the frame of a 3ftx4ft carry box at the rear of my tractor.. rotten box-sections to cut out and new ones to weld in place and I must say, the welder performed pretty well.. no overheats, no delays, no failures and in just a few hours I had the frame repaired and nice and strong once more(just need a few checkerplates to finish the job). As for the welder.. well, for the price, ease of set-up and use I am well impressed. Still not certain about the quality of the f/c wire supplied but have not tried anything else in it yet.

I've used these for a few jobs over the last few months and have no complaints apart from sometimes the cable can come out as it is just a twist fit. Ideal for occasional use. Very lightweight and looks good too.

I bought this to weld some aluminium , wanted to use a spool gun and was put through to their customer support . Unfortunetly the wirefeed doesnt work correctly it goes slow then speeds up and doesnt react to any adjustments ie speed stays the same regardless of amps. This was same for both spool gun and internal wire feed motor.Disappointing as had potential to be a useful welder . Returned

Don’t miss out on this amazing little welder because you don’t know how electric worksIt’s small but it’s powerful, it came with the 16a plug which is fine if you’re using it in a workshop and have the sockets but it’s easy to swap to a standard domestic plug, I put a heavy duty standard UK plug on it with a 20A fuse, that will be fine for a standard UK twin socket which are tested at 20A and my whole sockets circuit supports 32a, because with welding it’s short bursts it’s pulsating rather than continuous current passing through the wiring so it’s not going to start a fire, it’ll hardly even warm the wiring, a fire is much more likely to happen from the welding arc or sparks. 16a is unfused and this machine is actually 20a so if you’re having problems check that!I initially installed it with a 13a fuse but I wouldn’t go higher than setting 7 then so had no issues with fuses blowing, if you’re worried about going over 13a that’s what you can do, otherwise you’ll obviously blow the fuse but then you’ll still have a 100a welder which you’ll be limited to anyway!It’s fine for beginners if you consider the above, it’s easy to use and lightweight. Not that I’m a beginner, I’ve been welding for 20 years and had many machines but this is a very good practical little one and is very flexible in all the ways you can use itI used it for welding car bodywork and also the exhaust and it worked great and went straight through the MOTI was welding all day with it with hardly any breaks and went through a few spools of wire, no issues whatsoever it did a great job

Fragile !! clean bench work !

Good piece of equipment